News / Schaeffler axlebox and gearbox bearings continue to ensure reliability of Hitachi Javelin high-speed trains
Date: 2016-08-04
Schaeffler axlebox and gearbox bearings continue to ensure reliability of Hitachi Javelin high-speed trains
As part of an ongoing bogie overhaul programme of Hitachi Rail Europe’s Class 395 ‘Javelin’ high speed trains, precision bearing manufacturer Schaeffler (UK) Ltd has successfully delivered more than 1,300 axlebox bearings and gearbox bearing sets to Hitachi Rail Europe’s flagship train maintenance centre in Ashford, with further deliveries planned this year.
Built by Hitachi, the Class 395 Javelin trains offer the fastest domestic service rail travel in the UK. In 2008, the Javelin completed its first rail journey from Ashford in Kent to London St Pancras in just 37 minutes. The Hitachi trains went into full passenger service in December 2009 on the High Speed HS1 rail route. The Class 395 is a dual-voltage electric multiple unit (EMU) built for high speed commuter services on HS1 and elsewhere on the Integrated Kent Franchise. The Hitachi Class 395 trains operate at a maximum speed of 140mph.
The trains consist of six-car units, with all axles on the middle four cars powered. The outer cars are unpowered. The bogies are bolsterless, with both powered and unpowered bogies sharing a common design to simplify maintenance. Each 6-car unit can work in multiple with another, creating 12-car trains.
Since the Hitachi train has been in service, Schaeffler UK has worked closely with Lucchini UK, the company responsible for the bogie overhaul on the Class 395. From its Manchester base, Lucchini UK provides a full wheelset service package for the Class 395 trains, including inspection, re-wheeling, reprofiling, axle skimming and supply of new axles. The company also specialises in the inspection, overhaul and maintenance of wheelsets, train gearboxes and final drives to UK-based operators and train maintenance contract holders.
Lucchini and Schaeffler UK have collaborated on a number of improvement projects for the Class 395, including mileage extensions and condition monitoring of the drive train, including axles, traction motors and gearboxes.
Mark Hughes, Hitachi’s Depot Manager at Ashford in Kent commented: “Schaeffler continues to supply a quality service six and a half years after the introduction of the Class 395 into passenger service and has been fully supportive of Hitachi’s aspirations to safely extend Class 395 axlebox bearing life.”
The current overhaul programme, which started in 2014, has seen Schaeffler supply 480 gearbox bearing sets and 840 TAROL axlebox bearings to Lucchini. As Mike Wood, Commercial Manager at Lucchini UK commented: “We purchase the bearings from Schaeffler on a controlled programme covering the overhaul of wheelsets for the full fleet of 29 Javelin trains. The bearings are changed on each mileage periodicity governed by Hitachi. We are currently in the second overhaul periodicity and have full service support from Schaeffler in achieving to date full on time deliveries.”
TAROL axlebox bearings
TAROL (Tapered Roller Bearings) units from Schaeffler are used primarily as axlebox bearings on rail vehicles such as goods wagons and passenger carriages. Axlebox bearings comprise the interface between the wheelset and the bogie frame and so are subjected to extreme loads. TAROL units are double row tapered roller bearings supplied with factory-set clearance, greased and sealed for life. These high reliability units are therefore supplied ready-to-fit and are pressed onto the shaft journal in a single operation using a hydraulic unit. Due to the press fit of the unit on a shaft journal of a diameter within the specified tolerances, the bearing support achieves the required axial clearance.
As well as supplying TAROL units for the Hitachi Javelin train, Schaeffler is also supplying a variety of gearbox bearings. These include both cylindrical roller bearings and four-point contact bearings, which stabilise the gearbox shaft and support the transmission of forces. In doing so, the bearings must withstand extreme loads under complex environmental conditions such as high vibrations, high speeds and high temperatures.
Jeremy Spencer, Rail Sector Manager at Schaeffler UK comments: “Since the Class 395 was put into service, the axlebox bearings are replaced at regular intervals. Originally, the bearings were replaced, regardless of their condition, at 500,000 kilometres. However, by working closely with Lucchini UK, we’ve managed to extend this to 650,000 kilometres between bearing replacements.”
“We’ve also assisted Lucchini by providing non-intrusive condition monitoring units to measure the vibration of the axlebox bearings as they are returned to the Hitachi Train Maintenance Centre in Ashford, Kent, as well as for use on gearbox bearings at Lucchini’s Manchester depot. These handheld FAG Detector III vibration monitoring units are supplied with custom developed software to enable bearing vibration levels to be measured in less than one minute. Although this programme is still in its test phase, the objective is to use the vibration monitoring units to ascertain whether or not a bearing needs to be replaced.”
100 years’ experience in rail
Schaeffler with its FAG and INA brands boasts more than 100 years’ experience in the rail industry, with applications including axlebox bearings and housings; bearings and components for traction motors and gearboxes; railcar connectors; braking; tilting technology; and bearings for train doors.
With increasingly complex operating demands and more strict safety standards in the rail industry, Schaeffler’s test laboratories in Schweinfurt and Anting (China) are accredited as independent by different national railway authorities and provide customers with complete peace of mind. Spencer goes on to say: “As well as refurbishments, we are able to conduct functional tests on complete assembled bearings, specific individual components, materials and lubricants. Test rig simulations can also be conducted on bearings, which help to contribute to significant increases in the service life and maintenance intervals of rolling bearings for a wide range of rail applications.”
For more information, please contact Schaeffler UK’s Communications & Marketing Department on info.uk@schaeffler.com.
1.The news above mentioned with detailed source are from internet.We are trying our best to assure they are accurate ,timely and safe so as to let bearing users and sellers read more related info.However, it doesn't mean we agree with any point of view referred in above contents and we are not responsible for the authenticity. If you want to publish the news,please note the source and you will be legally responsible for the news published.
2.All news edited and translated by us are specially noted the source"TradeBearings".
3.For investors,please be cautious for all news.We don't bear any damage brought by late and inaccurate news.
4.If the news we published involves copyright of yours,just let us know.
